1、卸料前让搅拌罐全速运转几分钟
1. Allow the mixing tank to run at full speed for a few minutes before unloading
高速转动让混凝土充分搅拌,防止凝固,可以加一些水,方面出料。
High speed rotation allows the concrete to be fully mixed to prevent solidification, and some water can be added to discharge the material.
2、出料前先把出料斗溜槽打湿
2. Wet the chute of the discharge hopper before discharging
尽量将车停在平地上出料,出料前先把出料溜槽打湿,防止混凝土粘结在溜槽,容易清洗。
Try to park the vehicle on a flat surface for discharge, and wet the discharge chute before discharge to prevent concrete from sticking to the chute, which is easy to clean.
3、卸料不要大意
3. Don't be careless when unloading
出料时全程看着,免得放料工乱操作放料操作杆,每次罐子正反转中间位子时好停一下,保护减速机,托盘。
When discharging, keep an eye on the entire process to prevent the discharge worker from operating the discharge lever recklessly. Every time the can is rotated in the middle position, it is easy to stop and protect the reducer and tray.
4、搅拌罐冲洗干净
4. Rinse the mixing tank thoroughly
自上料搅拌罐一定要仔细的冲洗干净,多次反复正转反转罐体,使水无死角清理,多次加水清洗,保持罐体内部的清洁,无混凝土残留。
The self feeding mixing tank must be carefully rinsed clean, repeatedly rotating and reversing the tank body to ensure that there are no dead corners in the water for cleaning, and repeatedly adding water for cleaning to maintain the cleanliness of the tank interior and no concrete residue.
此外装料时注意清洁,如:
In addition, pay attention to cleanliness during loading, such as:
1、装料前先将搅拌筒反转
1. Reverse the mixing drum before loading
搅拌车一般露天停放,装料前先将罐里的积水和树叶之类的杂物排出,以免影响混凝土质量。
The mixer truck is usually parked outdoors. Before loading, the accumulated water and debris such as leaves in the tank should be discharged to avoid affecting the quality of the concrete.
2、全自动搅拌车装完料要记得冲洗进料斗
2. Remember to flush the feed hopper after loading
洗完后要关掉水箱进气口,打开水箱排气口排掉气体,因为气压下,水管连接不好的地方,容易渗水,影响其他车辆的。再次检查轮胎是否卡有石子铁钉等杂物,使用工具及时清理,因为停车时轮胎与地面接触的地方是检查不到的。
After washing, it is necessary to turn off the air inlet of the water tank and open the air outlet of the water tank to exhaust the gas. This is because under pressure, areas where the water pipe is not properly connected can easily leak water, affecting the safety of other vehicles. Check the tires again for debris such as stones and nails, and use tools to clean them in a timely manner, as the area where the tires come into contact with the ground during parking cannot be detected.
搅拌筒内外积污及残存的混凝土渣块时,以及在机修人员进入筒内进搅拌行自动上料搅拌车在工作时应注意什么检修和焊补作业时,需先关闭汽车发动机,使搅拌筒完全停止转动。
When removing dirt and residual concrete debris inside and outside the mixing drum, as well as when mechanical maintenance personnel enter the mixing line inside the drum for automatic feeding, what should be paid attention to during maintenance and welding operations? The car engine should be turned off first to completely stop the mixing drum from rotating.
在机修人员进入筒内工作期间,要保证拌筒内通风良好,空气新鲜,无可然气体及有害灰尘,氧气供应充足。在筒内使用电动工具操作时,操作人员要有良好的绝缘保护。
During the period when maintenance personnel enter the mixing drum to work, it is necessary to ensure good ventilation, fresh air, no natural gases or harmful dust, and sufficient oxygen supply inside the mixing drum. When using electric tools inside the cylinder, operators should have good insulation protection.
作时,不得将手伸入旋转的搅拌筒内,严禁将手伸入主卸料溜槽和加长卸料溜槽的连接部位,以免发生事故。
When working, do not extend your hands into the rotating mixing drum, and do not extend your hands into the connection between the main discharge chute and the extended discharge chute to avoid accidents.
以上就是小编总结的全自动搅拌车出料时要做好这些工作!,请大家在使用时遵循规章制度,生产。更多相关内容就来我们网站//capemaycitypolice.com咨询了解!
The above is the summary by the editor that these tasks should be done well when fully automatic mixer trucks discharge materials!, Please follow the rules and regulations when using and ensure safe production. For more related content, come to our website //capemaycitypolice.com Consultation and understanding!